当前位置: 代码迷 >> 综合 >> U-Boot直接引导zImage内核
  详细解决方案

U-Boot直接引导zImage内核

热度:93   发布时间:2024-01-17 23:35:01.0

 

         U-boot1.1.6只能只能就能过mkimage工具加工后的内核镜像文件。mkimage工具给zImage增加了一个64B大小的头。U-Boot是通过bootm命令来引导Linux内核的,bootm命令调用do_bootm函数来mkimage工具增加的头,最后调用do_bootm_linux函数引导去掉了mkimage工具增加的头的Linux内核,也就是zImage,启动的流程可以参考图解U-Boot:引导内核分析这篇博客。

     要让U-Boot直接引导zImage内核,只需在do_bootm函数中去掉对mkimage工具增加的头的分析,直接调用do_bootm_linux函数引导zImage内核即可。下面是经过修改的do_bootm函数,修改的部分用///包围起来了,省略号后面的就不需要改动了。这个函数common/cmd_bootm.c文件中。

[plain] view plain copy print ?
  1. int do_bootm (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) 
  2. { 
  3.     ulong   iflag; 
  4.     ulong   addr; 
  5.     ulong   data, len, checksum; 
  6.     ulong  *len_ptr; 
  7.     uint    unc_len = CFG_BOOTM_LEN; 
  8.     int i, verify; 
  9.     char    *name, *s; 
  10.     int (*appl)(int, char *[]); 
  11.     image_header_t *hdr = &header; 
  12.     s = getenv ("verify"); 
  13.     verify = (s && (*s == 'n')) ? 0 : 1; 
  14.     if (argc < 2) { 
  15.         addr = load_addr; 
  16.     } else { 
  17.         addr = simple_strtoul(argv[1], NULL, 16); 
  18.     } 
  19.     SHOW_BOOT_PROGRESS (1); 
  20. // 
  21.     //printf ("## Booting image at %08lx ...\n", addr); 
  22.     printf ("## Booting from zImage at %08lx ---by ce123\n", addr); 
  23. #ifdef CONFIG_SILENT_CONSOLE 
  24.         fixup_silent_linux(); 
  25. #endif 
  26.         do_bootm_linux  (cmdtp, flag, argc, argv, 
  27.                  addr, len_ptr, verify); 
  28. // 
  29. ...... 
int do_bootm (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) {ulong iflag;ulong addr;ulong data, len, checksum;ulong *len_ptr;uint unc_len = CFG_BOOTM_LEN;int i, verify;char *name, *s;int (*appl)(int, char *[]);image_header_t *hdr = &header;s = getenv ("verify");verify = (s && (*s == 'n')) ? 0 : 1;if (argc < 2) {addr = load_addr;} else {addr = simple_strtoul(argv[1], NULL, 16);}SHOW_BOOT_PROGRESS (1); ////printf ("## Booting image at %08lx ...\n", addr);printf ("## Booting from zImage at %08lx ---by ce123\n", addr); #ifdef CONFIG_SILENT_CONSOLEfixup_silent_linux(); #endifdo_bootm_linux (cmdtp, flag, argc, argv,addr, len_ptr, verify); // ......

接下来还要修改一下lib_arm/armlinux.c中的do_bootm_linux函数。这里主要是修改kernal的加载地址(theKernel = (void (*)(int, int, uint))addr)。这就要求我们将zImage内核下载内存的addr处。并且用bootm addr进行引导,默认的地址是0x30008000,如果直接使用bootm进行引导,则需要将内核下载到0x30008000,否则无法引导内核。

[plain] view plain copy print ?
  1. void do_bootm_linux (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[], 
  2.              ulong addr, ulong *len_ptr, int verify) 
  3. { 
  4.     ulong len = 0, checksum; 
  5.     ulong initrd_start, initrd_end; 
  6.     ulong data; 
  7.     void (*theKernel)(int zero, int arch, uint params); 
  8.     image_header_t *hdr = &header; 
  9.     bd_t *bd = gd->bd; 
  10.  
  11.  
  12. #ifdef CONFIG_CMDLINE_TAG 
  13.     char *commandline = getenv ("bootargs"); 
  14. #endif 
  15.  
  16.  
  17.     //theKernel = (void (*)(int, int, uint))ntohl(hdr->ih_ep); 
  18.     theKernel = (void (*)(int, int, uint))addr; 
void do_bootm_linux (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[],ulong addr, ulong *len_ptr, int verify) {ulong len = 0, checksum;ulong initrd_start, initrd_end;ulong data;void (*theKernel)(int zero, int arch, uint params);image_header_t *hdr = &header;bd_t *bd = gd->bd;#ifdef CONFIG_CMDLINE_TAGchar *commandline = getenv ("bootargs"); #endif//theKernel = (void (*)(int, int, uint))ntohl(hdr->ih_ep);theKernel = (void (*)(int, int, uint))addr; 

下面是引导信息:

U-Boot 1.1.6 (Mar 11 2012 - 14:06:15)


DRAM:  64 MB
Flash:  2 MB
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x240000, size 0x200000
2097152 bytes read: OK
## Booting from zImage at 30008000 ---by ce123

Starting kernel ...

Uncompressing Linux.............................................................
............................................................. done, booting the
kernel.

  相关解决方案